Netgear AC1200 WiFi Mesh Extender Setup

The NETGEAR AC1200 Extender creates a mesh network with your existing WiFi. Eliminate dead spots and improve range and connectivity for your iPads, smartphones, laptops and more. This extender suits best for an approx area of 1.2 sqft with providing up to 1200 Mbps speed. Netgear AC1200 mesh extender setup can be done by the below-mentioned steps-

Here we show the step-by-step procedure on how to set up the N300 Wireless Range Extender using the WPS button and using 192.168.1.250.

Netgear AC1200

How to Setup Mesh Extender via Wps

Setup Mesh Extender via Wps
  1. Firstly plug-in your Netgear Range Extender close to your router and wait for the power light to turn solid amber.
  2. In case power light doesn’t come up, press the power ON/OFF button.
  3. Once the Power light turns solid amber push the Wps on Netgear AC1200 WiFi Mesh Extender for two seconds.
  4. Now you will see a blinking light on the Netgear range extender.
  5. Within a minute push Wps button on the Router too, and you will see blinking Wps on the router too.
  6. It hardly takes 10-15 seconds for extender to get connected with the router.
  7. After the configuration is successful the blinking lights will turn solid green.
  8. You can confirm it by login to website mywifiext.net.
  9. You just need to connect a device now like a laptop or cell phone and as you do that client LED will lit-up.
  10. Unplug your extender and place it halfway between your router and the place where you need WiFi signals.
  11. Furthermore for optimum strength place Netgear AC1200 WiFi Mesh Extender away from large electronic appliances.
  12. Download Netgear Wifi Mesh extender manual.

If you still can’t set up your Netgear WiFi Range Extender, get in touch with the experienced technicians

Setup Netgear AC1200 via 192.168.1.250

  1. Firstly, Plug the Netgear AC1200 WiFi Range Mesh Extender into wall outlet.
  2. Wait till the power LED turns solid amber.
  3. In case Power light doesn’t come up, press the power ON/OFF switch.
  4. Now grab any of your cell phone or laptop and connect them with Netgear_ext in your WiFi list.
  5. Once connected you need to open a browser and in the URL or Address bar you need to type 192.168.1.250 or mywifiext.net
  6. It will directly take you to “New Extender Setup“.
  7. You will have to create a netgear account for your Extender there.
  8. After that it will search for all the available WiFi connections.
  9. You need to select your main WiFi network among them and punch in the password too.
  10. Lastly, Just follow the On-screen intructions and your Netgear AC1200 WiFi Range Extender will be configured.
Setup Netgear AC1200

NETGEAR AC1200 MESH EXTENDER SETUP LED STATUS

You will be able to spot 4 different LEDs on this extender. The router link LED, the client link LED, the WPS LED, and the power LED. Let’s take a look at what their statuses are and what they stand for.

  1. The router link LED flashes a solid green when the connection between the router and the extender is strong and Amber when it is good. Although if the connection is bad it shows you a red signal. It also remains off when no connection is made between the router and the extender.
  2. The client link LED denotes connections between the extender and the client devices. It shows a green solid light in the event of a strong connection and a solid Amber when the connection comparatively good. Sometimes it comes up with a red light to denote a poor connection. It does remain off when no device is connected to the extender.
  3. The WPS LED shines green when a successful WPS connection has been made and blinks the same green light when the connection is in process. It remains off when no connection via WPS has been made. It is more secure to have the WPS connection that not using it.
  4. The Power LED shows a solid Amber while booting the device and a solid green when the device is on. It remains off when there is no power supply to the device.

HOW TO RESET NETGEAR AC1200 MESH EXT?

In order to reset the ac1200 extender, you will need a straightened paper clip. Then you can insert the clip into the reset hole and wait for five seconds until the power LED flashes a solid Amber. Leave the button and wait for 30 seconds after which your extender LEDs will all flash green once and then go off. The reset procedure completes here and you can then reprogram the extender in your way.

HOW TO UPDATE THE FIRMWARE OF THE NETGEAR AC1200 MESH EXT?

In order to update your ac1200 mesh extender you will need to login to your Set uplink. there enter your SSID and password as prompted. this will lead you to the access page. find the maintenance button under which you will find the updates option. Under the updates, option-click on check for updates, download the updates to your computer. You may need to unzip the files.

Go back to the setup link and find the updates button Under the maintenance option. This time click on Browse files and continue to upload the update files that you just downloaded. the files will get uploaded and the extender firmware will get automatically updated. Generally whenever you log in The updates are checked unless you change the settings. During the update, the extender will remain non-functional, run a power cycle after the firmware update for optimal performance.

NETGEAR AC1200 MESH EXTENDER NO INTERNET?

This problem may arise due to a lot of reasons. one of them could be a problem from the side of your ISP. The problem could be from a fault on your end too. One of the most frequent reasons for this problem is that people tend to enter the wrong information Then prompted during the setup. This leads to wrong information being fed into the extender and hence the extender will not be able to connect to the router.

This will result in an Internet cut off. in order to avoid this problem always make sure that the information you enter during the prompt of the setup is accurate and does not contain any mistakes. If you enter any inaccurate information then the solution would be to reset the extender and reprogram it from the beginning.

Another reason for the Internet not working could be the extender being too far away from the router. always make sure that the extender is in an optimal position And always in a range of the router. Please note that the extender only released the network from the router and does not have any network of its own. A few minor bugs could also cause the problem and can be easily fixed if the router is reset to the factory settings.